Thank you watching video.
Thank you watching video.
Please SHARE and SUBSCRIBE to BiBi Kid Studio
For more infomation >> WATCH LIVE: The National for May 30, 2018 — Fake Death, Pipeline Project, Roseanne Barr - Duration: 1:04:58. 
For more infomation >> Liberals blame Trump for Roseanne tweet - Duration: 7:15. 
For more infomation >> Kim Kardashian may be using her brand for good: Kennedy - Duration: 2:03. 
For more infomation >> "Principles For Life" - Pastor Wilkerson - Sunday PM 5-27-18 - Duration: 1:16:01. 
For more infomation >> Democratic candidates for governor square off in debate - Duration: 1:27:55. 
For more infomation >> Kresl twins of Carroll High School sign for college sports - Duration: 0:40. 
For more infomation >> Sanity phase of trial begins for Goleta-area man convicted of murdering his family begins - Duration: 0:21. 
For more infomation >> Fire Burns Home Of Family Looking For Child's Liver Transplant - Duration: 1:57. 
For more infomation >> Golf highlights - Wolff's birdie wins national championship for Oklahoma State - Duration: 2:56. 
For more infomation >> More California voters opting for mail-in ballots; it's not too late to get yours - Duration: 0:38. 
hello and welcome to another one of our videos this one I means he's looking at
reinforcing puppet bodies the public bodies is basically foam and sometimes
they get very flattened squash particularly when you carry your puppets
in a suitcase or something like that when you're on tour and just they tend
to go flat so what you can do is add some boning which is gives it a lot a
lot more strength and keeps it a lot more it gives it more form particularly
when you have foam that's quite light and soft so I'll show you how to do that
so what we're going to use for the ring is some PVC piping the thinning is
thinner gauge stuff is good this is an electrical one conduit but then we're
going to use a saw to split it first in half then into quarters and that's what
we have here and then split that down the middle into the aides
so we get a flexible but strong piece of PVC
now you can calculate it to go on the inside of the foam or the outside
probably prefer to have it nicely snugly fit it inside the foam so I have made a
ring a circle that is right there of the size I want so over a flame or some heat
I'm going to heat this to approximately 77 degrees make sure you don't burn
yourself until it starts to just soften then on my circle my mold I'm going to
start wrapping it around then the opposite direction like this I know that
as it melts that goes on to the circle fine go right round the whole circle
so that you have finally got it overlapping the other one now you could
do this without heating it just make a circle but heating it helps it to retain
its shape without any stress cut that to length so that there's still an overlap
then to secure it I'm going to make a couple of holes with a knife so that
they are countersunk at the same time
then with the two marks that were scored by that I can go through to the other
side turn that over and come from the inside so that you get a countersink
on the inside of it then with a knife or a saw I'm going to cut a very thin
little wedge piece sort of like that and so that little wedge is going to go
through the two holes until it goes in tight
then I'm gonna take a flat-headed nail and a pair of pliers so I don't burn
myself is to heat it up to 67 degrees or so not too hot but hot enough to then
melt that pin which is now a rivet into the countersink
he just a little more and flip it over and do the other side
so if you do the other one you now have it riveted less than solid now it will
glue with some contact glue into there but I've made it to so that it will fit
right in the middle so with a sharp knife craft knife I'm going to slice
down the middle of that to the depth of the off the blade more less and go right
round and then in that I'm going to put the ring and then glue that so that it's
down by about a centimeter or half an inch so I have room to sew when I'm
closing the body of the puppet so folded down half of that you just pinned it so
that I can have access to putting the ring on and apply some contact loop
around there fold it back up to close it off so there we have it embedded into
the phone
Đăng ký:
Đăng Nhận xét (Atom)
Không có nhận xét nào:
Đăng nhận xét